|
|
|
|
|
| | INOZINC is a two-component water base inorganic zinc silicate primer. | | |
| | INOZINC is recommended to be used directly to metal as a self-priming primer/coat to provide a long term protection of steel structures against corrosion. Typical uses are for structural steel, bridges, all marine and land-based oil and gas production facilities, and all steel structures exposed to severe weather conditions or exposed to moderate chemical spillage and fumes. | | |
| • Excellent long-term performance without topcoating even in marine?environment.
• Single coat application is sufficient for excellent protection even on surfaces contaminated by firmly adherent rusts.
• Fast cure, water resistance and hardness are developed in 2 hours.
• Resistance to mud cracking even at 125 microns thickness.
• Easy to repair, low cost maintenance.
• Water base, equipment can be cleaned up with water.
• Self-inspecting over organic contaminants, film cracks and disbonds immediately if applied over a contaminated surface.
• Cost advantage over multi-coat systems.
• Suitable to be topcoated, when required, by epoxy coatings.
| | |
| | • Method of Application : | Conventional spray, nylon or polyester bruch for small area only. When applying INOZINC Primer it is important to keep the product stirred and to maintain a flow to prevent zinc settling in the spray lines. Also, it is vital to use spray equipment that has not been contaminated with organic solvents | | • Mixing Ratio : | 3Kg (Comp A) to 7Kg (Comp B) | | • Mixing : | Add Comp.B (powder) to Comp. A (liquid) and stir well before application in order to ensure that a uniform consistency is achieved. Never mix more material than can be used within potlife. Mixed materials not used within potlife must be discarded. | | • Pot life : | 8 hours (higher temperatures will shorten polife sharply). | | • Thinner / Cleaner : | Do not thin. Clean applying tools by hot water. | | • Application Temperature : | 5-40 ?C at a RH not more than 85% . | | • Curing : | The reaction between the two-component (A & B) can not be guaranteed unless a temperature of at least 5°C is maintained for the mixture and the substrate until complete curing. Temperature of substrate should be at least 3°C above dew point to avoid moisture condensation during application. Relative humidity during application and initial drying should not exceed 85%. | | • Note : | • Coated surfaces by INOZINC should not be exposed to water, chemical fumes, or mechanical stresses before it is fully cured. |
| | |
| | • Component A : | liquid | | • Component B : | powder | | • Color : | grey | | • Gloss : | flat | | • Volume Solids : | 65 % | | • VOC : | 0.0 g/L | | • Flexibility : | Very Good | | • Solvent Splash and Spill Resistance : | Excellent | | • Temperature Resistance : | 375 ?C | | • Recommended film thickness : | 75-125 microns “dry” | | • Theoretical spreading rate : | 8.7 m²/L at 75 microns “dry” | | • Water resistance : | Excellent | | • Abrasian Resistance : | Excellent | | • Number of Coats : | 1 | | • Specific Gravity (mixed) : | 2.79 kg/L (DIN 51757). | | • Packaging : | Component A (liquid) : 3 Kg in 1 metal can Component B (powder) : 7 Kg in 1 metal can | | • Weather Resistance : | Excellent |
| | |
| Well-prepared-surfaces is an essential condition of coating successfulness. In general, surface must be clean, dry, undamaged and free of all contaminants prior to coating.
STEEL or GALVANIZING:
Remove all oil , grease, wax…etc from the surface to be coated by thinner S100 or S405.
Apply INOZINC as soon as possible after surface preparation to prevent any contamination.
| | |
| | • Dry to Touch : | 15 minutes (ASTM-D1640). | | • Dry to Handle : | 30 minutes (ASTM-D1640). | | • Fully Cured : | 2 hours | | • Note : | Drying times can be affected by many factors such as temperature, ventilation and coat thickness. Relative humidity should not exceed 85%. Higher temperatures will shorten the drying times. |
| | |
| • Keep components A & B in a cool and well ventilated place, protected from freeze, heat and direct sunlight.
• Shelf life is two years from packing date in unopened original containers at 5 to 40°C. Containers should be kept tightly closed.
Safety:
• Well ventilated conditions should be provided during application.
• Do not breathe or inhale mist.
• Wear air-mask and avoid skin or eye contact.
• This Product is for professional use only. Not for residential use.
| |
|
|
|
|
information in this data sheet and in all our data sheets are given to the best
of our knowledge based on laboratory testing and practical experience. Final results
depend on following instructions and on consumer skill. Our responsibility is limited
to providing products that Conform to samples and specimens provided by us. Due
to technical needs, we reserve the right to change any given specification without
notice.
|
|
|
